As the title says, I'm looking for a Linux/macOS-compatible EPROM programmer. I'd like to be able to program parallel (E)EPROMs in the 27xxx range. The newer XGecu programmers seem to not be compatible with Linux/macOS, and the selection of TL866(II) clones is too overwhelming for me to be able to choose one.

Any suggestions?

This photo shows the power conversion side of two versions of the same board. Input is up to 60V DC, board converts to 5V and then down to 3.3V.

The top board works correctly all the time. But the bottom board has strange issues. Everything works perfectly when I connect it to my bench power supply at 53V. The board powers up with no problems. When I connect it to the daisy chain of other boards, it suddenly will no longer power on, despite ~54V being passed through correctly to downstream boards.

This is a real head-scratcher for me, and I'm having trouble making sense of it. I'm not so much looking for The Solution as to what steps I should take to troubleshoot this. There were some issues attaching the image, so in case it doesn't show up.

https://photos.app.goo.gl/MCx7Q4BDbKTv68EJ8

Circuit is for controlling the fan on a Raspberry Pi, just on/off according to temp, no PWM. Not sure about the diode as it has a .7V drop and it's a tiny brushless DC motor. No markings on the fan so I measured the current with a multimeter when hooking it up to a USB charger. Circuit was adapted from here using what I have on hand.

Suggestions? Any advice is greatly appreciated!

*EDIT: Confirmed, this circuit works on a Raspberry Pi 4. Base was wired to GPIO 17 and manually tested using commands:

raspi-gpio set 17 op dh

raspi-gpio set 17 op dl

I didn't use a breadboard, just hack-n-slash with the wires coming out of the fan, the leads on the thru hole components, a jumper connected to gpio 17 as a socket for the base/resistor lead, and heat shrink tubing for insulation. Folded it up as I closed the housing. Case combo including heatsinks and fan here.

Do any of you have experienced good products for tinkering together with a 3 year old?

I thought about something like a giant breadboard with simple connectors to switch on a light or play a sound or something.

It doesn't have to be too fancy, just sturdy and safe to play together with an adult.

Thanks!

This is my electromagnet.

Hello there, This oscillator is a 0V +10v DC oscillator, which after current passes through the capacitor, it produces a -5v +5v AC on the resistor.

We've all heard that AC removes DC component and let's AC pass by. I understand the dynamics of this circuit in case the oscillator were operating with AC (capacitive reactance), however this oscillator is DC, the voltage across the capacitor never changes polarity (since the other side of circuit is ground), so what gives? And why the 10V DC is split on half +5 -5 volts after the capacitor? Thank you!

Hi! I'm working on an arduino project that has a -12v/0v/+12 psu. +12 is fed directly into arduinos voltage regulator, so there's also a +5v line available. I need to convert a -5v+5v signal to 0v+5v to feed it into arduinos analogue input and I've already mocked up a schematic in circuitjs based on an opamp that seems to do what I want. The only problem is that it needs -5v to shift the signal to be unipolar. I know that I can invert +5v using another opamp, but maybe there's some simpler way? I'd really like to avoid adding another opamp just for this? In this schematic I used simple voltage divider to get the needed voltage, but I guess that's not the best approach?

TLDR: I have -12v, 0v, +12v and +5v, what's the easiest way to get -5v?

Hi!

I have bought a Geberit shower toilet/bidet with a motion sensor but it's aimed at the front while the toilet is installed sideways. So I've opened the thing up and I can take out the motion sensor, but the cable it's connected to is too short to do anything with. So I'm looking to buy/make an extension cable, but I have no idea on how to find it. So I took pics of the connector and I'm hoping you can help me find the type of connector (and if someone has a buy link: even better!). Thanks!

edit: https://www.jst.com/products/insulation-displacement-connectors-wire-to-board-type/vr-connector/ this looks like the socket, but the pitch seems wrong?

I'm trying to repair an arcade PCB with intermittent audio. The board on top is the audio board, the bottom board is the everything else.

There is a short or poor connection somewhere in this 96 pin DIN, press-fit connector.

I have OEM replacements, and would like to install new ones, but really have no idea how to do it properly (if you can even do it properly). My first thought was to do the following:

• Physically cut the pressfit connection to remove the plastic housings
• individually remove each cut pin from the PCB
• 3D print a "frame" around the connector area to minimize PCB flex, and use an arbor press to insert the press-fit connector

If anyone else has suggestions, I'm all ears!

I'm trying to replace the jet engine fan inside the PSU of a Nu 1.1 with a Noctua equivalent and am having trouble identifying the connector. The PSU is a Delta Electronics Model EDPS-250AB A, Part Number 400-5494-91.

I have taken several pictures of the fan connector and its header in the hopes of identifying the connection. I originally thought it was a JST-EH 2.0, but it is not, and the only means of comparison that I currently have.

Photos here: https://imgur.com/a/JQVahV3

Please help!

My room thermometer is consuming a full stack 3 AAA batteries in just 24 hours. I opened it and found that maybe the component circled in green is burnt (CAZB).

Can you please help me identify what it is in order to replace it?

Thanks!

I lost my electric fence tester, probably the pigs ate it. But I opened it once to resolder the earth wire and found it's really just a voltage divider with resistors and leds, so I can probably rebuild with stuff I have. What resistor values though? 2k to 10k V run through the fence. If any of you good people have a diagram, a formula or an idea, please help.

I wanna run a HR202 moisture sensor and an Arduino. Yes, I picked a HR202 to challenge myself to make it work. I already have some easier-to-use SHT40 in stock.

This sensor can only run with AC 1.5Vpeak max. So, I've created this little circuit to provide AC, and I'll only read it when the oscillator output is HIGH, so I can read it briefly at the same time with the help of Arduino's ADC. Could this circuit work? Thank you.

Here's a power cable from a Cmt-ex1 Sony CD player. This connector used to be connected to the inside of the power supply. However, I had to disassemble it because I needed to replace the motherboard for the CD player. I found this CD player at Goodwill, but the wire was poorly connected with a completely different cable. It was patched together using electrical tape and wire connectors. If there isn't any type of connector like this in the world. how could I Frankenstein it with another cable without it looking somewhat ugly.

The original cable was called E81093 (UL) NISPT-2 VW-1 105C 2X18AWG, C(UL) NONINTEGRAL SPT-2 FT1. Also the yellow plastic says Amp with a + on top of the M. this CD player is from 2000.

I want to use an IC that will take x4 3.0 PCIe lanes, and adds a USB 3.1 controller.

This ASMedia one looks ideal, but doesn't appear to be available to the common folk: https://www.asmedia.com.tw/product/E0CYQ4fSpaQxdjzA/f32YQ14SmApn1wNA

There's also https://www.ti.com/lit/ds/symlink/tusb7340.pdf - but that costs 22USD with LCSC, as well as being much slower (only using x1 lane)

I'm finding it hard to Google as well, because it seems to bring up complete products rather than ICs.

Can buy a whole card on eBay with the ASM3242 on it!

Can anyone help here please?

Mates bread maker stopped working so I had a look inside and saw this burned resistor.

I'm guessing the heat changed the colors a bit so wondering if anyone has experience in reading cooked resistor values.

I removed it from the PCB and measured it at 403 Ohms.

Thanks for any help.

Hello everyone! I'm designing a PCB and I have some doubts about how to connect the 4 resistors at the top to capacitor C34. They are 4 traces, and all of them terminate at the same pad of the capacitor. As I have currently placed them, are they connected correctly? Or should I connect them in a different way?

My goal is to drive an infrared LED like (this SFH 4727AS) to control IR remote controlled devices (for example a TV).

I can already output the signal on a pin of my microcontroller. The signal has a carrier frequency of 38kHz.

I am however limited to a 5V 1A power supply and would like to drive the LED as close to the 5W psu limit as possible.

I first thought about using a MOSFET like this AO3400A together with a resistor, but decided it was worth using an LED driver, do you agree?

Now I'm looking at this PAM2804 constant current LED driver but I'm not sure if I can just supply my signal to the EN pin. The EN pin is meant for PWM-dimming, so does that mean the output is smoothed to prevent flickering?

I'd love to hear your thoughts about how I should go about this. Thanks

First of all, I apologize for the lack of a "formal" schematic... I tried to draw one out, but got buried in the nuances of it :)

Second, I've done enough research to have some idea of what my problem is: namely, I need a decoupling capacitor in the mix. Problem is, I'm new enough to this that I'm not 100% sure where to put it, nor what capacitance I should use.

So the setup: -I'm using a Wemos(like) D1 Mini to drive 8 relays via an HC595 shift register -The D1 Mini microcontroller, HC595, and relay module are all powered by the same 5V DC and ground -The microcontroller addresses the shift register via 3.3VDC data pins -The relays power a water valve via a separate 24VDC power supply and transformer - plugged into the same AC outlet

And the problem: everything works just fine UNTIL I actually add the 24VDC power load. Once that's done, the results are very erratic... usually turning on the correct valve correctly, but rarely turning it off in the same way. As I mentioned, I intuitively suspect noise in the data caused by the sudden power to the valve... but it doesn't make too much sense since everything is on different power supplies.

Any guesses as to where I need to put some capacitor(s)? Thanks!!

Hi, I found an old cellphone battery (from a Pixel3A phone) and I'd like to reuse it for my robotics experiments. (link to images: https://imgur.com/a/Oj09tai)

2 questions:

1. how can I trasform the output connection to a more "standard" output connection (ideally V+ and V- wires)
2. how could I recharge the battery?

Any safety concerns, other than don't poke it? :D

If I wanted to make a USB desk fan from a spare CPU fan (input: 12V, 0.15A), could I just solder a resistor to the positive lead of the USB wire? I plan on getting an adjustable voltage booster, but I was curious if this was possible. I think I would need a 13 ohm resistor for USB 3.0.

I am looking for a Toggle switch that will allow me to actuate an actuator manually, or otherwise set the actuator to an 'automatic' mode, logic for which which I am coding on an arduino. The switch I want should have momentary On's for manual trimming that will spring back to an Off position, or it can be left in another maintained On position to signify the automatic logic should take over.

I had in mind something like a 2-axis Toggle switch that will have in the X-axis an MomentaryOn-Off-MomentaryOn configuration which will allow me to trim when in manual mode, but there should also be a fourth position (3rd Throw) above or below the 'Off' which would be a maintained On. Hopefully my diagram below explains the kind of switch I'm after too:

       On
       |

(On) - Off - (On)

I have spent about a day searching for something like this, and the only things I have found are a few old Cutler-Hammer aviation switches which seemed to do exactly this (8905K514, 8905K671, and 8905K608), but these are rare and expensive, and I wanted something I could easily get spares for.

I know I could achieve similar using a combination of two or more switches, but I feel it would be more elegant to have one switch that does everything. Does anyone have any suggestions?

Thanks in advance!

I bought a PWM Dimmer based on a 555 from AliExpress to regulate the brightness of a 12V 1A 1 meter LED strip, I already built one myself years ago on a perfboard but this one was the exact dimensions I needed for a project. I built mine from components from AliExpress and components found in old electronics so I thought nothing functionally would change The dimmer is this one https://www.diymore.cc/products/pwm-10a-speed-regulation-led-dimming-ultra-high-linearity-band-switch but I attached a real photo of the one I got from AliExpress My problem is that it isn't doing any regulation while connected to LED strips, I tried with the 1m one and with another light that has three 30cm LED strips in parallel Every other light or motor I connected to it seemed to make it work. I really have no idea what could be causing this, maybe it's sensible to capacitance? LED strips are two long straight parallel contacts but I don't think it's enough to cause anything as displayed here in the video: https://live.staticflickr.com/video/53017878188/54f865d36d/1080p.mp4?s=eyJpIjo1MzAxNzg3ODE4OCwiZSI6MTY4ODMxNzgwMCwicyI6ImI2MjZiMzk3MjExNTQxZWIyOTYwYzAyNTRmZDNhZDZjZTcwOWUxOGYiLCJ2IjoxfQ

Please no prejudice on that oscilloscope, it's good for what its made for, it's "calibrated", it shows a clean square waveform on my simple diy dimmer (photo to let you see what I mean with simple) versus what is shown in the video with the AliExpress one, an hybrid ramp/square. In the first part I show one of those LED strip that doesn't work, in the second part I show one that does work, just like every other light or motor I've tried

I tried adding an AUX jack to a car stereo with an internal CD player and no native support for one.

When I first did tests, simply attaching to one of the amp's input lines while the stereo was at min volume (1, not 0, more on this later) worked wonderfully.

To install the jack itself however, I thought that it may be dangerous to have the stereo send current to the AUX device and vice versa, so I thought about installing a switch to cut the stereo's audio input lines when using the jack and vice versa.

I thought about just muting the stereo, or turning the volume to 0, or using a dummy paused CD, but all of the three activate the mute line on the amp, which isn't a simple binary on/off deal, and activating it would also mute the jack.
Image

This is the original schematic of the amp circuit: Image
I attached to the IN1-4 lines like this: Image

I left the rear channels disconnected because a friend of mine suggested jumping two input lines could cause issues to the amp

However, once all was done, it wasn't working correctly. First of all, when I flip the switch, some signal from the stereo still gets through. It's very faint and you have to turn the volume way up to hear it, but it's there. This concerns me if it may lead to damage to either the plugged in device or the stereo, and if it could be the cause of the following issue.

Second, when a male to male cable is plugged in the other end (without even anything attached to the other end), a high pitched whine starts playing from the speakers. I tried bypassing the jack with alligator clips to the rear terminals, but it still happens, and when this happens I suddenly read a resistance of 7~8MΩ between either of the jack's channels and ground. I haven't tried another cable, but if I test the cable itself when it's unplugged I can't read anything between the rings.

I'm especially puzzled as to why there were no issues when I tried by tapping into the lines, but now that I did it """properly""" (at least in my head) it's problematic.

The full schematic for the stereo can be found by googling "BLAUPUNKT FIAT B-MPV CD-MP3 7645324316 SM"