126
submitted 6 months ago by luthis@lemmy.nz to c/asklemmy@lemmy.ml

Had someone contact me because a browser interface was 'down' and it was actually a cert issue. It surprised me that in an IT context, this person didn't have a basic understanding of SSL certs. They didn't even know how to add a cert exception.

It got me thinking, what basic ubiquitous things am I a dumbass about outside of IT?

Ive seen lots of 'fun facts' compilations, but it would be better to get a wide range of subject suggestions that I can spend 30 minutes each or less on, and become a more capable human.

Like what subjects would plumbers consider basic knowledge? Chemical interactions between cleaning products and PVC pipes?

What would an accountant or a landscaper consider to be so basic its shocking people can live their lives without knowing any of it?

For most areas of expertise, its difficult to know even what the basics are to start with.

you are viewing a single comment's thread
view the rest of the comments
[-] Shady_Shiroe@lemmy.world 9 points 6 months ago* (last edited 6 months ago)

EDIT: Sorry didn't mean to reply to your comment, I'm on mobile, can't tell posts from comments.

I believe knowing a little bit on how a car works helps you understand why maintenance is important or from getting scammed at mechanics, I loved old commercials like these that explain in such an easy way. https://www.youtube.com/watch?v=yYAw79386WI

Some skills I wanna pick up is how to micro solder, I deal with a lot of tech and sometimes you just need a type c port replaced and soldering iron is not the easiest tool for tiny pins.

[-] Tar_alcaran@sh.itjust.works 7 points 6 months ago

Some skills I wanna pick up is how to micro solder, I deal with a lot of tech and sometimes you just need a type c port replaced and soldering iron is not the easiest tool for tiny pins.

Good news, the broken component is a common 2 dollar chip!

Bad news, it's an SMD, and in the middle of a giant block of plastic and 2 more circuitboards.

[-] luthis@lemmy.nz 5 points 6 months ago

Learning about cars, engines and motorbike maintenance at this stage in life really opened my eyes. I could have easily been a mechanic or an engineer if I had the access to this knowledge when I was younger.

Now I do as much of my own maintenance as I can, and I'm pretty sure my engine will hit 400K before I start getting serious issues. None of it is overly complicated or difficult, and saves me money in the short and long term.

[-] Shady_Shiroe@lemmy.world 3 points 6 months ago

I was fortunate to have a dad who had the tools, space, and time to teach me how to do repairs, with the things he taught me I can save a lot of money buying a beat up car and fixing it up for usually 1/3 to half the price of a used one.

[-] PipedLinkBot@feddit.rocks 2 points 6 months ago

Here is an alternative Piped link(s):

https://www.piped.video/watch?v=yYAw79386WI

Piped is a privacy-respecting open-source alternative frontend to YouTube.

I'm open-source; check me out at GitHub.

[-] bloodfart@lemmy.ml 1 points 6 months ago

For microsoldering: you want the quick 861dw or one of the knockoffs and a bunch of tips. Sometimes you can get away without a microscope but usually you need one of those too. You need a swing arm mount for it because you often won’t be able to position your board under the objective of a tabletop mount.

You 100% cannot get away without a fume extractor. You’re gonna need low melt solder and flux, so you also need to be wearing disposable gloves.

You need a board holder because once all the solder in the area is liquified you don’t want the heavier parts sliding off the board because it’s propped up on a piece of wood at a ten degree angle.

If you wanna extend the amount of work you can do with just a decent iron: use flux and low melt to get everything on your usbc liquid at the same time so you can lift it off the board.

[-] Shady_Shiroe@lemmy.world 1 points 6 months ago

I found that using a soldering iron to be unweildy, which could either be a bad iron or my poor skills. I was thinking of maybe investing in future for one of those hakko hot air rework stations and see if it is any easier. Right now that's on hold, but totally something I want to try in the future, maybe as a hobby.

[-] bloodfart@lemmy.ml 1 points 6 months ago

Start with the hakko 888 or the weller equivalent. Learn how to solder big stuff first like tinning wires without burning up the insulation, big through hole joints according to the nasa guidelines, bell splices etc. it’s easier to see and judge how things are going with big stuff because you can see it better.

Use different tips to see what they do.

Remember that soldering is just brazing. You’re joining two metals by introducing a third.

Don’t start with a project you want to finish, just join a bunch of junk together, pull parts you don’t care about from old circuit boards and put different parts in their place.

Make little sculptures out of your trash.

Cheat with different kinds of flux till you don’t need to anymore.

Do the same things with smd parts.

It takes a long time to get good at soldering and no matter what anyone says you can’t just jump past the iron to hot air.

I mean, it’s possible. You’ll just never be able to fix mistakes or bridges you make with the hot air.

this post was submitted on 29 Feb 2024
126 points (95.0% liked)

Asklemmy

43400 readers
639 users here now

A loosely moderated place to ask open-ended questions

Search asklemmy 🔍

If your post meets the following criteria, it's welcome here!

  1. Open-ended question
  2. Not offensive: at this point, we do not have the bandwidth to moderate overtly political discussions. Assume best intent and be excellent to each other.
  3. Not regarding using or support for Lemmy: context, see the list of support communities and tools for finding communities below
  4. Not ad nauseam inducing: please make sure it is a question that would be new to most members
  5. An actual topic of discussion

Looking for support?

Looking for a community?

~Icon~ ~by~ ~@Double_A@discuss.tchncs.de~

founded 5 years ago
MODERATORS