I recently asked about having my coating re-applied, and the folks at the eye place had a warranty system, where if it came off inside of two years, they'd strip and re-coat the lenses. Might call them to find out if you're covered, or of they can tell you the stripping method.

If the lenses are plastic acetone will fuck them up.

If it is anything like the polycarbonate lenses on cars, it will take extremely tedious polishing, and then you'll have continuous issues with yellowing because polycarbonate is not UV stable.

With my auto body shop, I sanded the lenses to 2000 grit and used a polyurethane clearcoat. However, typical automotive clearcoats are not optically perfect. It does not matter with an automotive headlamp, and 99.9% of people will never see the optical properties unless I pointed them out specifically. That said, coatings like automotive clearcoats are designed to adhere to very specific types of substrates. What I was doing was WAY outside of the intended use. I doubt any of the lenses I clearcoated lasted more than 3-5 years as a result.

The PITA part of clearing lenses like I was doing with headlights is that ALL of the old coating must be removed first. If I didn't sand off every last bit of that coating, it was very noticeable in the final outcome. I had some tricks, but it is not possible to use course grades of sandpaper that would make fast work of it situation but require a primer to level in a typical body shop situation. This meant I had to start with 1k grit. That takes FOREVER to sand through a coating like what headlamps have.

Sanding anything like this is not compatible with optical precision lenses. I have also played with telescopes and building my own eyepieces while also dreaming about grinding my own mirror for a large dob. Optical precision in lenses is OP insane levels. I don't have the vocabulary to express just how tiny the difference is between good, okay, and absolute trash in optics.

Combining my experiences in these areas, there is absolutely no chance that you'll be able to polish or abrade then polish an optical lens and yield an acceptable outcome. No matter what you try, the coating will abrade/polish at a different rate than the exposed sections of the underlying polycarbonate lens. This will always result in an uneven surface at optical quality kinds of levels. You would need a sanding block capable of matching the contour of the lens perfectly so as to only abrade away the coating section before contacting the lens.

While clearing headlamps, I had one of two tricks. If all I was doing is shooting the lenses, I would mix my clear without any additional reducer (special solvent) and with a fast catalyst. This required special gun settings and higher pressures to avoid orange peal textures. If I was mixing clear for other panel work, I had to do a few misting passes with clear in between my other panel work. The thin misted coating limits the exposure of the underlying polycarbonate to the solvent present in the clear. If I did a regular wet pass like I would with a panel, the lens would react to the solvent and looked like a shattered windshield.

I don't know of anyone else that has ever clearcoated headlamps like this. While my work may not have lasted as long as a typical clear, it was a far better solution than polishing, which reoxidizes within a few weeks and worse with the increased exposed surface area after each polishing. For higher end cars, dealers would just pay me to install reproduction headlamps from LKQ, as these will last like the originals or better.

Those are the basics of what I know. I shared as an abstract way to help you understand the scope of what I know, and what you should expect based on this tangentially related expertise. I do not believe you can be successful at removing that coating. In automotive paint, it is not possible to just remove a clearcoat from any surface chemically without impacting the deeper substrate.

Just an FYI, I had that happen to my driving glasses a couple years back. My optometrist said that's because you cannot leave glasses in a hot car as the heat destroys the coating... OK thanks for telling me AFTER the fact, where do you THINK I am keeping a pair of glasses that you designed specifically for my driving vision? And by the way, I've been wearing glasses for over 35 years and always had the anti-glare coating for night driving, what did you change that is suddenly making them self-destruct when they are stored where I need them???

Yeah they had no answers for me. But OP, if you left your glasses in your car, that's probably what happened to the coating.

I have worked in optical, that coating is the anti-reflective coating that is coming off. You cannot take that coating off. It is baked on. Harsh chemicals will destroy the plastic lenses. It just degrades and comes off after a while, generally if it is less than 2 years they should be under warranty.

I've had good results removing the coating with armor etch, but be warned that the uncoated plastic lens are now more prone to scratches. I was able to extend the life of my glasses about 6 months before I got annoyed with the microscratches building up, was able to save up for a new pair.

In the future, I highly recommend using Kimwipes to clean off your lenses day-to-day. They're little papers designed to wipe off lab equipment without leaving any scratches or residue, and you don't need to spray them with any cleaner either. Just a dry wipe until the lenses are clean. If I'm careful about how I use them, a wipe can be reused 2-3 more times before disposal.

Since I started using them, I've never had problems with the antiglare coating coming off.

Half of the picture is blurry, put them back on!

Next time ask your lenses without. Mines are the same, I have a new prescription & just told the shop "no". No anti-blue, no ant-reflection, no nothing, just the hardest material available.

Toothpaste with hydrated silica might polish it off with enough elbow grease. Should be gentle enough to not fuck with the polycarbonate lens itself. I've done it with success but the toothpaste I used was an institutional brand and not really fit for putting in one's mouth.

Commercial toothpaste with hydrated silica would be marketed as "microbeads" or some such.

A paste of baking soda and water on cotton balls worked well for me, albeit tedious.

Reading glasses or regular?

You fix it pretty easily by just getting the lenses entirely replaced. If you have vision insurance, you can do it entirely for free

Hi Costco glasses guy, I see you.