12
APC server rack with threaded holes instead of cage nuts (lemmy.world)
submitted 1 year ago by snekerpimp@lemmy.world to c/selfhosted@lemmy.world
16 comments fedilink hide all child comments

Just picked up an APC 48u server rack. There were no pictures of it in the post and I did not notice until I got it home and set up, that the rack rails have threaded holes instead of square cage nut holes. I can’t seem to determine the thread size and pitch, and have a thread gauge coming. Until then, does anyone know anything about this? The people I grabbed it from had used self tapping machine screws and drove them in with an impact wrench. Is this what APC had intended, or is there some $300 proprietary screw I have to buy from them?

top 16 comments
sorted by: hot top controversial new old
[-] gripworks@lemmy.world 7 points 1 year ago

While I can't speak for your rack in particular, most pre threaded racks are either 10-32 or 10-24 screws.

You can buy them easily on Amazon.

I work in television, and in our equipment room we have 50 racks that are pre threaded. And we use these: [Amazon link](Penn Elcom S1032/HP/WA/100 High Point Rack Screws with Washers - Set of 100 https://a.co/d/g13kPzw)

[-] snekerpimp@lemmy.world 1 points 1 year ago

This is what I thought too, but both #10 threaded bolts I have are too small, one will thread, the 24 ones I believe, but you can wiggle them, enough to wiggle them out with out turning them.

[-] EmoPolarbear@lemmy.emopolarbear.com 2 points 1 year ago

They're 12-24, we use these at work.

[-] snekerpimp@lemmy.world 1 points 1 year ago

#12-24 are way to big, can’t even get them to catch the first thread.

[-] twack@lemmy.world 2 points 1 year ago

I know you said this is wrong, but my APC racks that look just like that also use 12-24 pilot point screws. They do have a little cutting notch that clears out the paint when you screw them in though

[-] snekerpimp@lemmy.world 1 points 1 year ago

This is honestly the answer I was looking for. Someone who has this in service. Thank you so much. I’ve seen these bolts on APCs website, I was thinking it was for cutting the powder coat but wanted to make sure. Thank you again!

[-] jake_jake_jake_@lemmy.world 1 points 1 year ago

12-24 from a telco guy, buy a 12-24 tap to help take the paint off

[-] snekerpimp@lemmy.world 1 points 1 year ago

Heading to the depot as we speak. Thank you

[-] scrubbles@poptalk.scrubbles.tech 3 points 1 year ago

I learned this the hard way, there is a difference between a "data rack", which is the one with cage screws, and a "network rack", which comes with the threaded machine screws. I believe switches have standardized screws

[-] snekerpimp@lemmy.world 2 points 1 year ago

I will try and attack it from this angle. Thanks for the input!

[-] SheeEttin@lemmy.world 1 points 1 year ago

Rack screws are pretty standard. You should be able to get a big pack for cheap from the usual online suppliers. Looks like you would want M6x16mm screws.

[-] snekerpimp@lemmy.world 1 points 1 year ago

I have m6 cage nuts from my last rack and they are WAY too big. An M5-0.8 will thread about half way in and then bind, making me think it’s a thread pitch issue?

[-] tburkhol@lemmy.world 2 points 1 year ago

If they're #10 (US) screws, they'd be 4.8mm major diameter and 24 or 32 threads per inch, so something like M4.8-1.06 or M4.8-0.78. If M5-0.8 thread half way, it sounds more like 10-32.

If you're outside the US, that might be why the previous owners resorted to the ugga-dugga. That will (probably) have wrecked those holes for either their factory pitch or whatever the owners used. You might consider getting a 5MM drill and a 6mm hand tap. You might have fair luck with 10-32 screws, depending on how hard they are to get in your country.

[-] snekerpimp@lemmy.world 1 points 1 year ago

In the US, figured they were a bizarre metric thread someone hammered a sae thread into. #10-24 is sooooo loose though, it’s hard to imagine they would design it with that much slop.

[-] Saik0Shinigami@lemmy.saik0.com 1 points 1 year ago

No idea on the screw question... but the labels are off by one screw spacing. The holes that are "close" are where the U labels should change.

[-] snekerpimp@lemmy.world 1 points 1 year ago

Yea, it’s only on that one bracket too, keen eye.

this post was submitted on 10 Jul 2023
12 points (87.5% liked)

Selfhosted

40152 readers
432 users here now

A place to share alternatives to popular online services that can be self-hosted without giving up privacy or locking you into a service you don't control.

Rules:

  1. Be civil: we're here to support and learn from one another. Insults won't be tolerated. Flame wars are frowned upon.

  2. No spam posting.

  3. Posts have to be centered around self-hosting. There are other communities for discussing hardware or home computing. If it's not obvious why your post topic revolves around selfhosting, please include details to make it clear.

  4. Don't duplicate the full text of your blog or github here. Just post the link for folks to click.

  5. Submission headline should match the article title (don’t cherry-pick information from the title to fit your agenda).

  6. No trolling.

Resources:

Any issues on the community? Report it using the report flag.

Questions? DM the mods!

founded 1 year ago
MODERATORS
ruud@lemmy.world
CannaVet@lemmy.world
Loki@lemmy.world
HybridSarcasm@lemmy.world
devve@lemmy.world
HybridSarcasm@lemmy.hybridsarcasm.xyz